MEID Soulution from Tony at mobile-files.com

mms678

Tony at mobile-files.com posted his MEID solution using CDMA-Workshop 3.4.1
1 w4 f! S: ~: p$ f% j
* t' S! ]" o2 D4 q- g: b  T! Phttp://mobile-files.com/forum/showthread.php?t=111278

Thank him.
       
, E% L0 _- X/ u! J翻译
, ?, N5 C/ w# N/ b  a8 o
http://translate.google.com/tran ... ad.php%3Ft%3D111278
$ K, G2 H) z: G6 U9 Ghttp://babelfish.yahoo.com/trans ... ;btnTrUrl=Translate
, F, c6 F( T' h; N/ y! m" K9 F
Is there any need to assign a read access (所需阅读权限) to this post?

5 d+ Q- Y0 _! z8 k: Z* ?! P[ 本帖最后由 mms678 于 2009-7-13 06:04 编辑 ]

2b6c3d729918489

Thanks mms, let me copy the threads.
大家注意文中的地址0x00A00000-0x012D0000,会找到6个MEID和ESN
7 }+ V, Y$ |8 w+ k2 c找到后马上写入.因为重启后地址可能会变
0 B- l$ e. E7 e2 S写完后不要马上重启.在搜索信号和时候.输入##DEBUG#. (即##33282#).然后等机器搜索信号并连接成功..
然后再重启..
" }" m- e7 |9 K5 l; s
------------------------------------------------------------
. r/ ?  F$ @$ QPalm Pre MEID Solution (CDMA WORKSHOP)
8 P9 Z, n" p$ O+ @: J! x# ]: kWe've been checking on everyone's progress with the Palm Pre MEID Solution. And we've realized you guys have made it more complicated than it is. We've received some appropriate requests lately, so here's a guide using CDMA Workshop.. In theory, it should work just fine with QXDM by directly replacing the MEID/pESNs, or zero-ing it out and using MEID write command.

1) By now you should understand how to set your phone in PASS THROUGH MODE and have your SPC
. I0 u3 ]! H7 Y  e- M' Y
  Y8 d$ w7 O: }$ D- c2) Connect with CDMA Workshop (v3.4.1 was used) and send your SPC

8 _  c; f2 B. N% |8 L/ X3) Under the Security tab, in the MEID section, press Write button using UNIVERSAL RAM method. Then select Scan memory for MEID... and use this range:
+ W) V0 x% o  \0 U: U
0x00A00000-0x012D0000
+ q! D* a, o, }" |& T) _2 f
3 Y8 @$ ~: ?$ X! i7 j  I+ d4 Xnote: The phone must return 6 MEID locations and 6 pESN locations. If anything less, don't attempt to write as you will brick the radio.

- c8 b! b- P; i2 W( Z4) As soon as you have a list of locations, immediately write the MEID as sometimes even rebooting the phone may change one of the locations.
2 d; D5 {1 z! P# G0 g
. ?. [$ ?# m5 ?& O: n5) Once it finishes writing, CDMA Workshop will confirm the success. Do not reboot or power off the device yet. The device will start searching for signal again, wait until it finds a signal and confirm the MEID by dialing ##DEBUG#. Once confirmed and you have a signal, you're set and safe to continue on (powering off, usage, etc).

EricHoo

3.41 is a must?

gzmob

好像没成功吧？

sirenbooboo

thank you very much for sharing this, i'll have a try on my own one late this day, but will 2.7cr version also work?

ioukgk

亮点是Ev标志！！

sirenbooboo

人家是米国人。。。。

yglaotu

哪位勇敢小白再试验下？然后发个报告上来，大家盼望着的……

EricHoo

很想当小白鼠，只可惜拿不到电信数据。。。

Jeromekp

唉，看不懂，没机子，羡慕。。。

xxrake

原帖由 sirenbooboo 于 2009-7-13 08:40 发表
: H- J$ q' }4 Xthank you very much for sharing this, i'll have a try on my own one late this day, but will 2.7cr version also work?

6 d/ D! }7 k' O& x6 G8 W$ A1 @! l
2.7是不行的
3.41,可以确认这办法行得通

qinray

从http://www.mobile-files.com/foru ... t=111278&page=2上看到, 已经确认该方法可行.
: ?( N7 ~6 ^0 H  G+ H' R( ~

I can now confirm; Tony's Method WORKS!
1 g9 y8 S& V# \: D* V% I& B
If you have an "unaltered" phone, it will work with this caveat: You MUST read the exiting MEID in FIRST, using the Default method, then type in your new MEID, then do the scan memory and write using RAM method.

fanconi

..................脚印.........顶

tonyee

注册版的workshop3.41可不好找呀

大大鱼

关键还是cdmaworkshop3.4需要注册啊