|
新的软件,无敌的软件啊,他可以自己调整自动关机的电压,调低的话就可以延长开机时间了,而对于我来说,这个软件的精华之处莫过于修复背光了!2 I0 j" x8 Q$ f8 I6 i2 P
& |8 s7 F I0 W6 u) Z# s" r
T3等用户都知道,调节背光的滑块即使调到最左边(最低),晚上还是刺眼,而使用了他!调到最低时候几乎等于了关闭背光!!而调最右边,和原来的最亮程度是一样的!怎么样?超级好东西吧!
8 t4 d8 H# k) k4 j; u1 S5 ?& N
9 e& y8 F, S& D9 d: w- f: [T3电力不好,这样晚上看出不担心刺眼,而且还可以看得时间更长的,简直是太好的东东了,这个是Full版本,没有任何限制,要卸载也不需要额外软件,他软件的菜单内就有卸载选项!
+ E* I: r' b' d* q2 X5 g& s h) {) ?4 ^" r( G
而且这个软件只有13K的大小啊,爽!
" g& |" p4 w+ ?0 {( ~, S0 [6 K, K: D6 U$ G
PS:这个软件的图标是由掌印的FC兄重新替换~; u6 } e9 I& S8 j0 F
! A. F+ a# m! _# _' @& }9 e# l-----------------------------------------------------------------------------------------------
3 E/ R) e0 H! }, S[Installation] - C' N1 M6 Y& {* P8 L2 x) C
Remove previous version (if any) of FullPower and perform a soft reset. ! o% y+ {, H. P+ B/ U
This is important step! Install the program in the internal RAM
8 V9 M. r. y' nvia HotSync or by other means. Installation to card is not supported. v" T# a' y8 M, b$ r4 A0 ~* z
. {0 }# K) `+ Y[Supported devices]
; Q0 v/ T" u0 i/ o% k8 RCurrently (as of v1.09) the shutdown control feature is supported on the
6 y3 x+ \# V+ Bfollowing devices:
" y; t6 u( S: @9 qpalmOne Tungsten|C 0 c) ?* N) g+ p3 }1 c2 N& N
palmOne Tungsten|T2
" C* i0 P& W n. }+ EpalmOne Tungsten|T3 : D# i8 ?! h+ K. {3 [
palmOne Zire 71 ' Z) X9 r* g; M9 G8 g" X; l: I8 G, U
Garmin iQue 3600 1 D, d1 t2 b8 r% G. H
Sony CLIE PEG-NX60 $ I0 S% N+ l" n# ]1 B, P
Sony CLIE PEG-NX70 / |. ^0 i. m8 A3 O% `
Sony CLIE PEG-NX80
0 D( ?/ K1 z+ @7 Y' E- eSony CLIE PEG-NZ90
' B( \# e" t! M% f) [Sony CLIE PEG-TJ35 0 H/ ^, |* ~2 T" f0 q$ W
Tapwave Zodiac (minimal threshold here is 358 cV; this limitation will be removed later) : Y5 m" @9 N# M# v
5 i$ a d4 d: t- d; d6 q
These devices generally work with FullPower, but the ; h ^7 s I' }# G5 f% s& p
current voltage setting may be wrong when shutdown voltage is set
- M: O5 P+ R) A7 xto low values (320-350 cV):
6 \& \$ ?0 W- w, H6 U# T, q" HZire 72
1 x- P/ J$ @: UTungsten|E / C4 Y. {9 G' p8 L; {' @& j' V
Tungsten|T5 z) m/ {/ {2 d9 \
( ?. [3 R4 q& h* |
Other PalmOS 5 devices should also work.
4 ?# Y' R( Q# K7 D3 h5 p2 K$ a; X8 o+ W! f1 Z
The brightness control feature is known to work on the following devices: & d6 K! Y! `( g7 j1 n
Zire 72 ) k; K) f: J* h5 D4 v% u
Tungsten|T3 / ?5 @1 R! R2 X) v
Tungsten|T5 b: C# B& g2 `* c( J0 ?6 a# W
0 y6 q/ h$ V3 T) s% cIt is expected that all newer palmOne devices will work. * l. m6 l" o2 o) z/ @
Please report any successes/issues to support@mobile-stream.com 2 i8 D* |1 _* D+ i% B" T1 s5 a
/ _9 h* H3 _" g# |
; |$ H+ c9 `9 i[General advice on shutdown threshold setting]
% _; u! v5 U- OUsually it is safe to set the lower threshold to 345-350 cV. For example, most palmOne devices usually have default limit at about 365-370 cV so setting the threshold to 350 will give good additional amount of working time.
/ S& i9 v l5 W9 Z* `, c3 V: r9 S4 P) v
Please note, the voltage values that are shown in the ZLauncher, FileZ and basically any third-party program are wrong. This is because of PalmOS 5 implementation of SysBatteryInfo() system function. ! J% H C9 W2 c0 [9 i4 O$ X
! i, R4 i0 ^% L6 BTo restore the default shutdown threshold setting, soft reset the handheld. ; p# {, F$ a0 A( {, ?# K8 C
& l# C7 y5 i! l& Q" V9 z
[Uninstallation] 3 z" Q2 U; V* E' ], Y
Select the "Uninstall" menu item in the application pull-down menu.
u% p6 j/ @/ B7 v, j3 _& c( ?+ t
[Author] - M/ h3 }7 z3 v; C( O' j' c9 h
Copyright (c) 2005 Mobile Stream. All rights reserved.
2 k" \# t. i' m: |! J- C4 V
, u3 _0 Q2 D; G) K) T1 s
: y8 k D4 }4 C..软件在此<<<<<<------------- http://www.treo8.com/bbs ----------->>>>>> |
|